1、 Application scope and working mode of filter element ultrasonic cleaning machine

滤芯超声波清洗机是适合于各种化工行业、金属拉丝机、化纤行业、净水设备等行业，主要清洗被脏尘、粉末、胶剂、碎屑等堵塞的内孔盲孔等。这些部位人手很难接触到，通过超声波清洗机能对深孔、细缝和隐蔽处清洗干净。

The filter element ultrasonic cleaning machine is suitable for various chemical industries, metal wire drawing machines, chemical fiber industries, water purification equipment and other industries. It mainly cleans the inner hole and blind hole blocked by dirty dust, powder, glue, debris and so on. These parts are difficult to reach by hand. Deep holes, fine seams and concealed places are cleaned by ultrasonic cleaning machine.

滤芯超声波清洗机广泛应用于：机械行业、表面处理行业、仪器仪表行业、电子行业、医疗行业、半导体行业、钟表首饰行业、化学生物行业、光学行业、纺织印染行业、石油化工行业、玉石饰物加工行业、眼镜行业等。利用机械转动臂将滤芯在超声波清洗机中匀速转动，超声波对滤芯表面及细孔进行不间断轰击，清洗速度快，清洗效果好，清洁度高，达到所有被堵塞细孔内脏物全部洗清的效果。

Filter element ultrasonic cleaning machine is widely used in: machinery industry, surface treatment industry, instrument industry, electronics industry, medical industry, semiconductor industry, watch and jewelry industry, chemical and biological industry, optical industry, textile printing and dyeing industry, petrochemical industry, jade jewelry processing industry, glasses industry, etc. The mechanical rotating arm is used to rotate the filter element at a uniform speed in the ultrasonic cleaning machine, and the ultrasonic bombards the surface of the filter element and fine holes continuously. The cleaning speed is fast, the cleaning effect is good, and the cleanliness is high, so as to achieve the effect of cleaning all internal organs of blocked fine holes.

二、超声波清洗机使用注意事项

2、 Precautions for use of ultrasonic cleaning machine

超声波清洗机在使用的过程中一定要注意使用规则，滤芯超声波清洗机在使用的过程中一定要切记注意事项。滤芯超声波清洗机电源及电热器电源必须有良好接地装置。这对机器能否正常的运转十分重要。另外，电源电压变化超出机器允许范围时，应立即暂停使用，避免出现用电问题，或者因为电路问题对机器产生损害。

Pay attention to the use rules during the use of the ultrasonic cleaning machine, and remember the precautions during the use of the filter element ultrasonic cleaning machine. The power supply of filter element ultrasonic cleaning machine and electric heater must be well grounded. This is very important for the normal operation of the machine. In addition, when the power supply voltage changes beyond the allowable range of the machine, the use shall be suspended immediately to avoid power problems or damage to the machine due to circuit problems.

如有物体跌落超声波清洗槽内，应及时取出，否则会磨损缸底。切记被清洗物体不应直接放在槽底(超声辐射面)清洗。

If any object falls into the ultrasonic cleaning tank, take it out in time, otherwise it will wear the cylinder bottom. Remember that the object to be cleaned should not be directly placed at the bottom of the tank (ultrasonic radiation surface) for cleaning.

超声波清洗机不应频繁开、关超声(间隔应在1分钟以上)，以免功率器件浪涌电流过大损坏。开启超声开关时应注意发生器散热风扇是否运转正常，否则易因过热损坏器件。超声波清洗机清洗缸缸底应定期冲洗，不宜有过多的杂物或污垢。

The ultrasonic cleaning machine shall not be turned on and off frequently (the interval shall be more than 1 minute) to avoid excessive surge current damage to power devices. When opening the ultrasonic switch, pay attention to whether the cooling fan of the generator operates normally, otherwise it is easy to damage the device due to overheating. The bottom of the cleaning cylinder of the ultrasonic cleaning machine shall be washed regularly, and there shall not be too many sundries or dirt.