服务热线电话
400-6188-756
多槽手动超声波清洗机的使用
来源:http://www.sinokohl.com/ 时间: 2023-10-27 浏览次数: 0
多槽手动超声波清洗机的使用方法如下:
The usage method of the multi slot manual ultrasonic cleaning machine is as follows:
将发生器与清洗槽连接电缆接好。
Connect the cable connecting the generator to the cleaning tank.
将槽内注入选用的清洗液。
Inject the selected cleaning solution into the tank.
将发生器接入220V±10% 50赫兹交流电源。
Connect the generator to a 220V ± 10% 50Hz AC power supply.
打开发生器电源开关,电源指示灯亮(此时槽内液体开始振动空化)。
Turn on the power switch of the generator, and the power indicator light will be on (at this point, the liquid in the tank will start to vibrate and cavitate).
使用多槽手动超声波清洗机时,应注意事项包括:
When using a multi slot manual ultrasonic cleaning machine, precautions include:
设备必须放在通风、干燥的区域,发生器后侧的风扇孔应定期清洁。发生器四面留有通风口,以使气流畅通无阻。
The equipment must be placed in a ventilated and dry area, and the fan holes behind the generator should be cleaned regularly. There are ventilation openings on all sides of the generator to ensure smooth airflow.
超声波清洗槽必须放入液体后才能开机工作,低水位高度>100mm(底振式)且水平放置,换能器在侧面时,为清洗槽槽沿100mm处,如在空气状态开机会损坏机器。
The ultrasonic cleaning tank must be filled with liquid before starting up and working. The low water level height is greater than 100mm (bottom vibration type) and placed horizontally. When the transducer is on the si
de, it is necessary to clean the tank along the 100mm edge. If starting up in air, it will damage the machine.

de, it is necessary to clean the tank along the 100mm edge. If starting up in air, it will damage the machine.

当清洗缸体温度为常温时,切勿将高温液体直接注入缸内,以免导致换能器松动而影响机器正常使用。
When the cleaning temperature of the cylinder block is at room temperature, do not directly inject high-temperature liquid into the cylinder to avoid loosening the transducer and affecting the normal use of the machine.
定期检查换能器,切勿使其变潮及撞击,以免造成不必要的损失。使用完毕后,应关闭总电源。关机后不要立刻重新开机,间隙时间应在1分钟以上。
Regularly inspect the transducer and do not let it become damp or collide to avoid unnecessary losses. After use, the main power should be turned off. Do not restart immediately after shutting down, the gap time should be at least 1 minute.
以上是使用多槽手动超声波清洗机的步骤和注意事项,供您参考,建议根据实际情况加以调整。
The above are the steps and precautions for using a multi slot manual ultrasonic cleaning machine for your reference. It is recommended to make adjustments according to the actual situation.
相关文章
-
科尔CNC高压清洗机,360°旋转喷淋,油污一键剥离效率翻倍 2026-04-27
-
科尔高压去毛刺清洗机,6kg高压+定制试洗,机械零件洁净无死角 2026-04-26
-
全自动高压喷淋清洗机,9kg高压加持,汽车铝铸件45秒洁净出炉 2026-04-25
-
8kg高压单工位旋转喷淋清洗机,水表壳油污一键清零,去污率超级高 2026-04-24
-
五金去毛刺难题迎克星,高压去毛刺清洗机凭实力降本增效 2026-04-18
-
空化效应≠万能!揭秘全自动超声波清洗机为何必须搭配定制清洗剂 2026-04-15
-
全自动超声波清洗机避坑指南!三槽联动清洁+防氧化,98%工业企业都选对了 2026-04-08
-
配件生锈老化别扔!超声波清洗机:一键除锈,让旧件焕新价值 50% 2026-04-07
-
别被低价碳氢清洗机坑惨!我宁可不卖,也不做偷工减料的良心生意 2026-04-06
-
别误解工业清洗!通过式清洗机:专啃工业重油污,不是设备无用是认知不足 2026-03-27

新闻中心




行业新闻







鲁公网安备37011202000628号