安装气缸垫圈时，要注意电机的旋转方向，应保持顺时针方向；它也应该接地。油缸清洗机正常启动后，空机将运行几分钟，然后正常工作。冬季使用时，必须预热12-24小时，然后加水调试。
When installing the cylinder gasket, first pay attention to the rotation direction of the motor, and keep it clockwise; It should also be grounded. After the oil cylinder washer is started normally, the empty machine will run for several minutes and then work normally. When using in winter, it must be preheated for 12-24 hours, and then added with water for debugging.
在使用滚筒清洗机时，要记住行点测试，然后空转运行2-3分钟，检查传动系统和输送带的运动情况，保持平稳状态，确认一切正常，方可生产。不仅如此，还要时刻注意气缸清洗机的运行状态。
When using the roller washer, remember to conduct spot test first, and then run it for 2-3 minutes at idle, check the movement of the transmission system and conveyor belt, keep it stable, and confirm that everything is normal before production. Not only that, but also pay attention to the running state of the cylinder cleaner at all times.
工作结束后，清洁后的气瓶不能停放在运输车上，按下停止按钮停止整机。此外，清洗机中的清洗液应定期加水和一定比例的污垢清洗剂补充消耗，使液位保持在一定高度。
After the work is completed, the cleaned gas cylinder cannot be parked on the transport vehicle. Press the stop button to stop the whole machine. In addition, the cleaning liquid in the cleaning machine should be regularly added with water and a certain proportion of dirt cleaning agent to supplement consumption, so as to keep the liquid level at a certain height.

在全封闭系统中，使用溶剂清洗金属，因为零件清洗机采用的是独立式蒸馏系统，确保所有清洗过程中在蒸汽蒸馏后溶剂保持雾状状态，且溶剂的清洁度不会改变，有效成分在清洗方面的质量要求。因为作为直接用水清洗的基础，是无法保证水经过蒸馏后的清洁度的，所以零件清洗机必须使用过滤装置和大量的水才能有效地实现清洗效率，零件表面需要配合其他设备进行清洗机工作。优良的品质有效提高 效率和的优点是零件，降低沸点是清洗槽设计进入真空环境的主要方式，因此在蒸馏零件时，余热可以有效保证气化过程，明显会提高工作效率，零件清洗机每小时清洗周期达到十次以上。
In the totally enclosed system, the solvent is used to clean the metal, because the parts cleaning machine adopts an independent distillation system to ensure that the solvent remains in a mist state after steam distillation in all cleaning processes, and the cleanliness of the solvent will not change, and the quality requirements of effective ingredients in cleaning. As the basis of direct water cleaning, the cleanliness of distilled water cannot be guaranteed, so the parts cleaning machine must use a filter device and a large amount of water to effectively achieve cleaning efficiency, and the parts surface needs to cooperate with other equipment for cleaning. The advantages of good quality, effective efficiency and energy saving are parts. Reducing the boiling point is the main way for the design of the cleaning tank to enter the vacuum environment. Therefore, when distilling parts, the waste heat can effectively ensure the gasification process, which will obviously improve the working efficiency. The cleaning cycle of the part cleaner can reach more than ten times per hour.
清洗机和零件时需要使用一些零件清洗溶剂，溶剂的缺陷是会对空气造成污染，但我们将零件清洗机设计为全封闭系统，对空气污染所带来的获得明显的控制，同时由于水基在工作过程中需要依靠表面活性剂的技术途径，而且活性化学品不能有效分解水资源造成的污染，因此水资源中会有大量的化学残留物，造成严重的污染。经相关部门计算，零件清洗机整体清洗后，可能对环境造成的污染或相对较大，水污染小于溶剂量的2000倍。而部分清洗技术在环境污染后，由于蒸馏技术的结合，所以造成的污染基本上会被完全切断在蒸馏箱中，所以不必再考虑以后的处理方案，而溶剂工业已经提供了特殊的输送系统，采用了封闭、的溶剂输送方式，确保零件清洗机的清洗工艺不受影响。
Some part cleaning solvents need to be used to clean the machine and parts. The defect of the solvent is that it will pollute the air. However, we have designed the part cleaning machine as a fully closed system, which can obviously control the air pollution. At the same time, as the water-based needs to rely on the technical approach of surfactant in the work process, and the active chemicals cannot effectively decompose the pollution caused by water resources, Therefore, there will be a lot of chemical residues in water resources, causing serious pollution. According to the calculation of relevant departments, after the overall cleaning of the parts washer, the pollution to the environment may be relatively large, and the water pollution is less than 2000 times of the solvent amount. After environmental pollution, due to the combination of distillation technology, the pollution caused by some cleaning technologies will basically be completely cut off in the distillation box, so it is unnecessary to consider the future treatment scheme. The solvent industry has provided a special transportation system, which adopts a closed and safe solvent transportation mode to ensure that the cleaning process of the part cleaner is not affected.
以上的精彩内容来自：喷淋清洗机济南科尔超声波设备有限公司专注通风管道多年，质量保证,服务完善,欢迎更多客户点击：http://www.sinokohl.com
The above highlights come from: Jinan Keer Ultrasonic Equipment Co., Ltd. has been focusing on ventilation ducts for many years, with quality assurance and perfect service. Welcome more customers to click: http://www.sinokohl.com