日常清洁 ：

　　Daily cleaning:

　　每次使用完去毛刺抛光机后，都要进行清洁工作，用抹布擦拭机器表面，确保没有抛光液或其他杂质残留在机器上。特别要注意抛光液不要溅射到机器上，因为这可能会损害机器表面。

　　After each use of the deburring and polishing machine, cleaning work should be carried out by wiping the surface of the machine with a cloth to ensure that no polishing solution or other impurities remain on the machine. Special attention should be paid not to splash the polishing solution onto the machine, as this may damage the surface of the machine.

　　抛光液管理 ：

　　Polishing solution management:

　　如果抛光桶里的水过热（正常水温范围在50°C），应及时换水。抛光液溅到机器上后，应及时擦拭干净，防止液体损害机器外表。

　　If the water in the polishing bucket overheats (the normal water temperature range is 50 ° C), it should be replaced in a timely manner. After the polishing solution splashes onto the machine, it should be wiped clean in a timely manner to prevent the liquid from damaging the appearance of the machine.

　　抛光针管理 ：

　　Polishing needle management:

　　放抛光桶时，抛光槽内若有抛光针，应及时清理。如果长时间不使用去毛刺抛光机，应将抛光的钢针清洗干净并放置在干燥的环境中，以增加其使用寿命。

　　When placing the polishing bucket, if there are polishing needles in the polishing tank, they should be cleaned in a timely manner. If the deburring and polishing machine is not used for a long time, the polished steel needle should be cleaned and placed in a dry environment to increase its service life.

　　控制面板保护 ：

　　Control panel protection:

　　去毛刺机闲置时，可以用胶袋套住控制面板，以防止灰尘进入。

　　When the deburring machine is idle, a plastic bag can be used to cover the control panel to prevent dust from entering.

　　润滑与维护 ：

　　Lubrication and maintenance:

　　定期对机器的润滑系统进行检查，确保润滑充分，并及时更换润滑剂。同时，要定期检查机器的各个部件，如砂带、压料棍等，根据需要进行调整和更换。

　　Regularly inspect the lubrication system of the machine to ensure adequate lubrication and promptly replace lubricants. At the same time, it is necessary to regularly inspect various components of the machine, such as sanding belts, pressing rods, etc., and adjust and replace them as needed.

　　机器校准 ：

　　Machine calibration:

　　定期校准去毛刺机的各个部件，以确保设备的正常运行和加工精度。

　　Regularly calibrate the various components of the deburring machine to ensure the normal operation and machining accuracy of the equipment.

　　操作 ：

　　Safe operation:

　　在操作去毛刺抛光机时，一定要遵守设备的规定，穿戴防护装备，防止发生意外伤害。

　　When operating the deburring and polishing machine, it is necessary to comply with the safety regulations of the equipment, wear protective equipment, and prevent accidental injuries.

　　备份与检查 ：

　　Backup and Inspection:

　　定期备份设备的重要参数和数据，以防万一。同时，定期对设备进行检查和维护，及时发现并故障，避免因设备问题导致的生产停滞。

　　Regularly backup important parameters and data of the equipment, just in case. At the same time, regular inspections and maintenance of equipment are carried out to promptly detect and resolve malfunctions, avoiding production delays caused by equipment problems.

　　储存 ：

　　Storage:

　　如果短期不再使用机器，将机器尽量放入室内，存放于0℃以上的空间，防止低温出现结冰情况。如果长期不再使用机器，需要把机器放在一个环境相对于干燥的空间中，可对机器内部部件涂抹防冻液，或是用防护套件进行保护，以防腐蚀。

　　If the machine is no longer in use in the short term, try to store it indoors in a space above 0 ℃ to prevent freezing at low temperatures. If the machine is not used for a long time, it needs to be placed in a relatively dry environment. Antifreeze can be applied to the internal components of the machine, or protective kits can be used to prevent corrosion.

　　本文的精彩内容由高压去毛刺清洗机提供知识提供，本网站还有很多的精彩内容，更多的内容您可以点击进入：http://www.sinokohl.com我们有专门的客服为您解答问题

　　The exciting content of this article is provided by the knowledge of high-pressure deburring cleaning machine. There are also many exciting contents on this website. For more content, you can click to enter: http://www.sinokohl.com We have dedicated customer service to answer your questions