1、原理：超声波清洗设备是利用超声波的高频振动产生能量，这种能量可以在清洗液中产生微小气泡，并在物体表面爆炸，从而去除物体表面的垢和杂质。具体来说，超声波清洗机由以下几个分组成：超声波发生器：超声波发生器是产生超声波的核心件，它通过电子振荡电路产生高频电信号，然后将其转换为机械振动，产生超声波。换能器：换能器是将电信号转换为机械振动的重要件，它通常由压电陶瓷等材料制成。换能器将超声波发生器产生的电信号转换为机械振动，并将这种振动放大，从而产生超声波。清洗槽：清洗槽是放置被清洗物品的地方，同时也是容纳清洗液的地方。清洗槽通常由不锈钢材料制成，能够承受一定的压力和温度。控制面板：控制面板是超声波清洗机的控制中心，可以设置清洗时间、功率等参数。

1. Principle: Ultrasonic cleaning equipment uses the high-frequency vibration of ultrasonic waves to generate energy, which can create tiny bubbles in the cleaning solution and explode on the surface of the object, thereby removing dirt and impurities from the surface of the object. Specifically, the ultrasonic cleaning machine consists of the following components: ultrasonic generator: The ultrasonic generator is the core component that generates ultrasonic waves. It generates high-frequency electrical signals through an electronic oscillation circuit, which are then converted into mechanical vibrations to produce ultrasonic waves. Transducers: Transducers are important components that convert electrical signals into mechanical vibrations, typically made of materials such as piezoelectric ceramics. The transducer converts the electrical signal generated by the ultrasonic generator into mechanical vibration and amplifies this vibration to produce ultrasonic waves. Cleaning tank: The cleaning tank is a place to place the items to be cleaned and also a place to hold the cleaning solution. The cleaning tank is usually made of stainless steel material and can withstand certain pressure and temperature. Control panel: The control panel is the control center of the ultrasonic cleaning machine, which can set parameters such as cleaning time and power.

2、使用方法

2. Usage method

准备：检查清洗机是否正常连接电源，确保正常通电。将要清洗的物品放入清洗槽中，加入适量的清洗液。

Preparation: Check if the cleaning machine is properly connected to the power supply and ensure that it is powered on normally. Put the items to be cleaned into the cleaning tank and add an appropriate amount of cleaning solution.

启动：按下启动按钮，超声波清洗机会自动进行清洗。控制面板可以设置清洗时间、功率等参数。

Start: Press the start button, and the ultrasonic cleaning machine will automatically clean. The control panel can set parameters such as cleaning time and power.

观察：观察清洗过程，注意清洗物品的变化。如果发现有异常情况，应立即停止清洗。

Observation: Observe the cleaning process and pay attention to changes in the cleaning items. If any abnormal situation is found, the cleaning should be stopped immediately.

取出：当清洗时间到达设定值时，机器会自动停止清洗。

Extraction: When the cleaning time reaches the set value, the machine will automatically stop cleaning.

此时可以取出清洗物品，用清水冲洗干净。结束：关闭控制面板上的电源开关，拔掉电源头，清理现场。

At this point, you can remove the cleaning items and rinse them thoroughly with clean water. End: Turn off the power switch on the control panel, unplug the power plug, and clean up the site.

3、超声波清洗机，是一种利用超声波振动原理进行清洗的设备。其利用超声波的振动作用将附着在物体表面的垢、油脂、杂质等分离和去除，具有清洗效果好、清洗速度快、清洗效率高、无需人工刷洗等优点。

3. Ultrasonic cleaning machine is a device that uses the principle of ultrasonic vibration for cleaning. It uses the vibration effect of ultrasound to separate and remove dirt, grease, impurities, etc. attached to the surface of objects, and has the advantages of good cleaning effect, fast cleaning speed, high cleaning efficiency, and no need for manual brushing.

本文由超声波清洗机友情奉献.更多有关的知识请点击:http://www.sinokohl.com我们将会对您提出的疑问进行详细的解答，欢迎您登录网站留言.

This article is a friendly contribution from the fully automatic ultrasonic cleaning machine For more information, please click: We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message