(1) The power supply of ultrasonic cleaning machine and electric heater shall be well grounded.

（2）超声波清洗机严禁在槽中没有水或溶剂时，千万不要启动，造成空振，造成振动头报废或损坏。

(2) It is forbidden to start the ultrasonic cleaning machine when there is no water or solvent in the tank, so as to cause air vibration and scrapping or damage of the vibrating head.

（3）有加热系统的清洗设备严禁无液时打开加热开关。

(3) For cleaning equipment with heating system, it is strictly forbidden to turn on the heating switch when there is no liquid.

（4）禁止用重物（铁件）撞击清洗缸缸底，以免能*转换器晶片受损。

(4) It is forbidden to strike the bottom of the cleaning cylinder with heavy objects (iron parts) to avoid damage to the converter wafer.

（5）超声波发生器电源应单独使用一路220V/50Hz电源并配装2000W以上稳压器。

(5) One 220V / 50Hz power supply shall be used separately for the power supply of ultrasonic generator, and a voltage regulator above 2000W shall be equipped.

（6）清洗缸缸底要定期冲洗，不得有过多的杂物或污垢。

(6) The bottom of the cleaning cylinder shall be washed regularly without excessive sundries or dirt.

（7）清洗机操作过程中请勿将手指放入清洗槽中，否则会感到刺痛或者不适。

(7) Do not put your fingers into the cleaning tank during the operation of the cleaning machine, otherwise you will feel tingling or discomfort.

（8）每次换*液时，待超声波起动后，方可洗件。

(8) When changing * liquid every time, wash the parts after the ultrasonic starts.

（9）采用清水或水溶液作为清洗剂，一定要禁止使用酒精，汽油或任何可燃气体作为清洗剂加入清洗机中。

(9) Clean water or aqueous solution shall be used as cleaning agent. Alcohol, gasoline or any combustible gas shall not be used as cleaning agent to add to the cleaning machine.

（10）当直接使用易燃液体清洗时，要尽量在短时间内完成清洗工作，并要求操作者不要离开现场。

(10) When directly cleaning with flammable liquid, try to complete the cleaning work in a short time, and ask the operator not to leave the site.

（11）当需要用腐蚀性或挥发性强的清洗液时，可采用间接清洗的方法。即：在清洗槽内加水，再将所需清洗液倒入适宜的容器内并放入被清洗物，然后将装有清洗液和清洗物的容器浸入清洗槽中，即可开始清洗工作，其效果与直接清洗相同。

(11) When corrosive or volatile cleaning solution is needed, indirect cleaning method can be adopted. That is: first add water in the cleaning tank, then pour the required cleaning solution into a suitable container and put the cleaned object, and then immerse the container containing cleaning solution and cleaning object into the cleaning tank to start the cleaning work. Its effect is the same as that of direct cleaning.

（12）使超声波清洗效果更好的方式，超声波清洗槽的温度为30~50℃，根据不同的清洗对象正确选择清洗剂。清洗剂一般分为水基（碱性）清洗剂、溶剂清洗剂和化学反应清洗剂。通常使用水基清洗剂，根据被清洗物的污染程度和污垢性质，选用不同的清洗时间。

(12) The temperature of ultrasonic cleaning tank is 30 ~ 50 ℃, and the cleaning agent is correctly selected according to different cleaning objects. Cleaning agents are generally divided into water-based (alkaline) cleaning agents, solvent cleaning agents and chemical reaction cleaning agents. Generally, water-based cleaning agent is used, and different cleaning time is selected according to the pollution degree and dirt nature of the cleaned object.

（13）在使用时禁止先开机后倒入清洗液，这样会使机器损坏。

(13) When in use, it is forbidden to start the machine first and then pour in the cleaning fluid, which will damage the machine.

（14）清洗物品不要直接放在清洗槽底部，应用专用清洗支架清洗筐，这样有利于提高清洗效果。

(14) Don't put the cleaning items directly at the bottom of the cleaning tank. Use a special cleaning support to clean the basket, which is conducive to improving the cleaning effect.

（15）尽量避免长时间连续工作，一般不超过30分钟为宜。

(15) Try to avoid working continuously for a long time, generally no more than 30 minutes.

（16）在使用时槽内清洗或脱气的溶液不要放入过少，一般在槽内2/3处更好。

(16) When in use, do not put too little cleaning or degassing solution in the tank, which is generally better at 2 / 3 of the tank.

以上是为大家介绍的有关层超声波清洗机http://www.sinokohl.com的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务

The above is the price of ultrasonic cleaning machine for relevant layers http://www.sinokohl.com I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service